List Name
There are many variations of passages of Lorem
Ipsum available, but the majority have suffered alteration in some form
HCI Cable Identifier
1.Clear, safe and quick cable identification on all types of de-energised cables
2.Cable identification Automatic recording and analysis of transmitting pulses:
– Amplitude
– Interval (time)
– Pulse direction (polarity)
3.High pulse current up to 100 A
4.Signal uncoupling by means of a flexcoupler for large cable diameters of up to 195mm
T32 Portable Cable Fault Location System
1.Applied to 1-500kV power cables
2.Surging (thumping) 32kV,delivers 2048 J
3.Maximum safety during application
4.Support LV TDR,ICE and ARM prelocation methods
5.Magnetic-acoustic pinpointing
6.Each part can be used independently
T20 Portable Cable Fault Location System
1.Applied to 1-35kV power cables
2.Surging (thumping) 32kV,delivers 1024J
3.Maximum safety during application
4.Support LV TDR,ICE and ARM prelocation methods(ARM is optional)
5.Magnetic-acoustic pinpointing
6.Each part can be used independently
TV30 DAC Test and diagnosis system for MV cables
1.Compact and lightweight, one-unit solution
2.Easy WIFI or wired based automatic control
3.Built in Time Domain Reflectometer(TDR)
4.Software support OTA
5.Uses well proven DAC excitation voltage for PD measurements (acc. IEC 60270)
6.Fully integrated dissipation factor(Tan Delta) measurement at DAC voltages
7.All in one testing and diagnosis of cables up to 20 kV
8.It can be easily fit into a car/ small van with a cargo load below 100kg
LB4/60A Smart Bridge for Cable Fault Location
1.No need to analyze waveform (TDR reflection based technologies)
2.Directly show the fault distance
3.Compact and lightweight
4.Suited for prelocating difficult, high-resistive faults
5.With burning function up to 60kV
6.One knob to easy operate
WL20 Cable Fault Pre-locator (TDR)
1.Rechargeable battery or mains operation possible
2.Stand-alone operation or operation in conjunction with surge generators (thumpers)
3.Dual operating concept (touch screen and rotary knob)
4.Supports multiple prelocation methods:LV TDR,ICE,ARM
5.Automatic detection of cable end and fault position
6.Rugged, durable, outdoor field-ready case
VLF-90KV Portable Hipot Test System
1.Digital frequency conversion technology, microcomputer control, pressure rise, pressure reduction,measurement, protection, etc
2.Multiple protection (over-voltage protection, overcurrent protection at high and low voltage sides),rapid action (when acting)
3.0.1Hz, 0.05Hz and 0.02hz multi frequency selection,large test range
4.Reporting
5.Small volume and light weight
VLF-40KV Portable Hipot Test System
1.Digital frequency conversion technology, microcom-puter control,pressure rise, pressure reduction,measurement, protection, etc
2.Multiple protection (over-voltage protection, over-current protection at high and low voltage sides),rapid action (when acting)
3.0.1Hz, 0.05Hz and 0.02Hz multi frequency selection,large test range
4.Reporting
5.Small volume and light weight
TBS-1000 Cable fault location system
1.Test modes: DC Proof, Surge Pulse (thumping) at 8/16/32 kV with fully variable output ranges at all voltage settings and facilitating full high energy capacitive discharge at all three volatge taps delivering up to 2,432 Joules. Variable Discharge Rate 6 – 10 second discharge/thump rate
2.Easily installed in vehicles
3.Built-in TDR, ARM, ICE and DECAY
4.Controlled by a tablet
5.Fully insulated design
6.Equipped with intelligent mode and expert mode, suitable for different test situations
T8 Portable Cable Fault Location System
1.Applied to 220V-11kV power cables
2.Surging (thumping) 15kV, delivers 900J
3.Maximum safety during application
4.Support LV TDR, ICE and ARM prelocation methods (ARM is optional)
5.Magnetic-acoustic pinpointing
6.Each part can be used independently
HC-10 Sheath fault location system
1.Testing, burning and pinpointing, direct resistance measurement, voltage and current limiter
2.Multiple signal reception methods used for different cable laying scenes(not just direct burial)
3.Mains and battery operated
4.Only one HV connection cable
5.Automatic evaluation and recommend test methods
6.Step voltage method for cable sheath fault pin-pointing
7.Easy and comfortable operation via touch screen and rotary encoder